公司新聞

攤鋪機攤鋪面不平整的原因及應對

來源：http://m.huatts.com/ 日期：2022-12-05

攤鋪機是一種主要用于高速公路上基層和面層各種材料攤鋪作業的施工設備，使用過程中，經常會出現各種大大小小的問題，你知道攤鋪機攤鋪面不平整的原因及應對嗎？下面濟南攤鋪機出租廠家為您講解。

The paver is a kind of construction equipment mainly used for paving various materials on the base course and surface course of the expressway. In the process of use, various problems, large and small, often occur. Do you know the reasons and countermeasures for the uneven paving surface of the paver? Next, Jinan Paver Rental Factory will explain to you.

①加熱溫度（熨平板地板溫度120度為宜）；

① Heating temperature (the temperature of screed floor should be 120 ℃);

②熨平板的平整度（底板連接不平整，底板表面不平整）；

② Flatness of screed (uneven connection of base plate and uneven surface of base plate);

③夯錘的速度（夯錘速度過低，出現坑洞；過高，表面起臺）；

③ The speed of the rammer (if the rammer speed is too low, holes will appear; if it is too high, the surface will rise);

④行走速度過快，有離析；

④ The walking speed is too fast and there is segregation;

點我：領取工程大禮包。

Click me: Get the project gift package.

⑤螺旋高度不合適，有離析；

⑤ Improper spiral height and segregation;

⑥找平裝置安裝不正確（裝反、超出感應范圍等），起波浪；

⑥ The leveling device is installed incorrectly (installed reversely, out of the sensing range, etc.), causing waves;

⑦路基不平整，參照物不準確，攤鋪厚度不一致，造成路面發白，突出時產生推移。料溫過低，也會造成攤鋪面離析和開裂。

⑦ The subgrade is not smooth, the reference is not accurate, and the paving thickness is inconsistent, which causes the pavement to be white, and the rolling will cause displacement. If the material temperature is too low, it will also cause segregation and cracking of the paving surface.
濟南攤鋪機出租

應對辦法：

Countermeasures:

作業前檢查熨平板底板是否平整，底板是否粘連雜物，及時清理和調整；

Before operation, check whether the screed bottom plate is flat and whether there are sundries stuck on the bottom plate, and clean and adjust it in time;

在加熱溫度達到要求后，再進行攤鋪工作；

Paving shall be carried out after the heating temperature reaches the requirements;

在料斗、刮板倉、螺旋處噴灑柴油，防止產生油斑；

Spray diesel oil at hopper, scraper bin and screw to prevent oil stain;

正確設定夯錘與攤鋪速度，螺旋的高度以高過攤鋪面的兩倍高度為宜；

The tamping hammer and paving speed shall be set correctly, and the screw height shall be twice higher than the paving surface;

正確安裝找平儀（或平衡梁探頭高度與連線的位置）；

Correctly install the leveling instrument (or the position of the balance beam probe height and connecting line);

時刻注意觀察參照物是否準確；

Always observe whether the reference object is accurate;

當路基平整度落差過大時，應提前墊料處理。

When the drop of subgrade flatness is too large, padding treatment shall be carried out in advance.

攤鋪機攤鋪面不平整的原因及應對就講解到這里了，您對此有什么想法或者問題或者需求，都可以隨時來我們網站http://m.huatts.com進行了解！

This is the end of the reason and solution for the uneven pavement of the paver. If you have any ideas, problems or needs, you can come to our website at any time http://m.huatts.com Get to know!

上一條：選瀝青混凝土要看性質及制備工藝

下一條：挖掘機的各種操作使用技巧